How to Troubleshoot an Aura Massage Gun That Won't Turn On

Troubleshooting an Aura Heated Massage Gun That Won't Turn On

A massage gun like the Aura Heated Massage Gun can provide soothing, warm relief to sore, tight muscles. But what if you go to use your massage gun and find it won't turn on? There are some troubleshooting steps you can try to get your aura massage gun working again.

Check the Battery Charge Level

If your aura massage gun won't power on, the first thing to check is the battery charge level:

• Make sure the battery is fully charged. Charge for several hours by plugging into a wall outlet using the charging cable.
• Try using your device while it charges to see if it will turn on when plugged in.
• Inspect the charge level indicators when charging or pressing the power button to determine if the battery needs to be replaced.
Reset the device by holding the power button down for 30+ seconds to reboot the system in case of any software glitches.

With most massage guns, a low, depleted or damaged battery is the most common reason for failure to turn on.

Examine All Power Button Issues

If the battery is charged but the aura heated massage gun still won't start, take a close look at the power button:

• Make sure the power button is not stuck and depresses/springs back properly when pressed.
• Check for any dirt, grease, debris or obstructions in the power button preventing normal operation.
• Inspect power button wiring inside to ensure no loose connections or detached cables.
• Test with multiple long presses to ensure contacts are working.

Any issues with the physical power button or internal switch contacts not triggering properly can lead to startup failure.

Assess Damage to Device Exterior

Carefully look over the whole exterior of your inactive aura massage gun for any signs of damage that could cause functionality issues:

• Look for cracks or external damage that may have impacted internal components.
• Check if any connectors like charging inlet or port covers are broken and exposing circuits.
• Determine whether the gun was dropped, got wet through use in the shower or otherwise sustained damage affecting operations.
• Feel for any loosening or rattling of casing parts that may be disconnecting vital parts.

Fixing physical device damage often requires electrical and technical repair expertise. Significantly damaged units may have to be replaced if unable to be repaired effectively.

Internal Troubleshooting Options for Aura Massage Guns

If you've covered the basics like battery, buttons and physical damage and your Aura massage gun still fails to work, more involved internal troubleshooting may be needed. Here are some options to test inside the device:

Inspect Internal Wiring

You'll need to open up the plastic housing of your massage gun to check the internal wiring. Look for:

• Any disconnected or loosening wiring connections
• Exposed wire from friction damage
• Accidental unplugging of motor connectors
• Corrosion or heat damage to wires from extended overuse

Reconnecting separated wires and covering any exposed areas with electrical tape may help get your device running again.

Assess Motor Function

The motor that drives the intense vibration is the heart of massage guns like the Aura. Check whether:

• The motor failed to engage and turn on
• Burnt motor windings cause immediate shut off
• Motor damage from overheating limits functionality
• Motor bearings, shafts or gears got obstructed or stuck

Unfortunately, most motor-specific repairs require professional technicians to carry out tricky disassembly and parts replacements.

Test Voltage Regulation

The circuitry regulating consistent electricity flow can malfunction over time. Watch for:

• Erratic motor behavior from uneven power
• Sudden shut off from voltage spikes
• Failure hitting full speed due to low voltage

Voltage regulation fixes involve electronics expertise for danger of shocks. But some loose solder joint connections may be an easier DIY repair.

Replace the Controller Board

If no other explanations arise for your aura massage gun failure, the issue may lie with the main controller board and integrated circuits.

• Components can short circuit or fail
• Software bugs may need reflashing
• Drops can jar connections loose
• Water damage can corrode circuit paths

Unfortunately controller board fixes are only possible by replacement with factory parts rather than repair. But this may restore function if no other options exist.

When to Call for Professional Massage Gun Repairs

While some basic checking and fixes are possible in a non-functioning Aura heated massage gun, more complex troubleshooting requires electronics repair expertise. It's best to seek professional service when:

Advanced Disassembly is Needed

Only open up your massage gun if comfortable working with electronics. Forcing open sealed components without knowing locations of cables, solder points and fasteners may cause irreversible damage. Professionals have the necessary training and tools.

Electrical Testing is Required

Always exercise caution when dealing with lithium-ion batteries and power circuits. Faulty wiring and shorted connections pose real electric shock risks requiring certified electricians.

New Parts Must Be Installed

While wires and even controller boards may be salvageable from donor devices, only factory original new components can reliably replace key parts like motors. This assures quality and safety are maintained.

Software Fixes Are Needed

Controller board failures often require software reflashing or resets best performed by company engineers with proper diagnostic setups. Their coding changes can restore full function.

Seeking professional repairs whenever advanced fixes are necessary makes sure your Aura heated massage gun is restored safely to working order if DIY efforts fail to resolve startup issues.

Preventing Aura Heated Massage Gun Power Problems

While even well-maintained massage guns can ultimately encounter issues turning on over time, you can take some proactive measures to minimize problems:

Avoid Overusing Your Massage Gun

Limit massage gun use to manufacturer recommendations, usually about 10-20 minutes per muscle area max. Excessive operation can overheat motors and overtax batteries.

Stay Away From Water

While designed to withstand sweat, moisture can still degrade internal components over time leading to corrosion or short circuiting. So avoid shower or wet use.

Handle With Care

Drops, especially on hard surfaces, can shake electronics connections loose or damage critical parts. Always take care not to drop your massage gun during transport or use.

Store Properly

Don't stash your massage gun tossing around loosely in a gym bag. Choose protective cases and compartments to minimize damage risks during travels.

Taking simple care and preventative steps goes a long way towards ensuring your Aura heated massage gun maintains reliable power delivery and avoids inconvenient failure to start issues requiring time-consuming repairs down the road.

Disclaimer: This article is for informational purposes only and does not constitute medical advice. Always consult with a healthcare professional before starting any new treatment regimen.